Showing posts with label Schematic. Show all posts
Showing posts with label Schematic. Show all posts

Electrical Schematic Symbols

0 comments

Electrical Schematic Symbols:

Electrical circuit schematic symbols are graphical sign, that is used to design electronic, electrical circuit schematic diagram. There is a quite adequate collection of symbol for electrical, electronic circuit. You can use this high quality schematic symbols to design your own schematic circuit diagram. Download high quality electrical schematic symbols image.

Electrical-Symbols
High Quality Electrical Schematic Symbols


Special thanks to the author of www.ARRL.org  for these high quality electrical schematic symbols.
This circuit schematic symbols are for educational purposes only, not for any industrial use.
Continue reading[...]

100 watt inverter schematic diagram – 12 Volt to 220 Volt

0 comments
Here this is a simplest circuit for 100 watt inverter for generating 220vAC from 12vDC. I say simplest because here in this inverter circuit a minimum number of components are used to design the schematic, which is quite difficult to make a circuit like this with further fewer components.

100 watt inverter schematic diagram


100
Fig: Schematic diagram of 100W inverter
This 100W inverter circuit works great for small loads like a fan or 2-3 bulbs/lamps. In this circuit as IC1 we used a CD 4047 IC to generate 100Hz frequency (180 degree out of phase). CD 4047 IC is from Texas Instruments. It is mostly used as Astable/Monostable signal generator device. In this circuit it is triggered as astable multivibrator by the capacitor C1 between the Pin 1 and 3 of CD4047. And VR1 is used to adjust the frequency of signal.

Four 2N3055 transistors are used to amplify the pulse trains that are pre-amplified by two TIP122 transistors. There used three transistors for each side (half cycle), one TIP122 & two 2N3055 transistor to drive the output transformer (TX in circuit). Four 2N3055 transistors are used as driving transistor. An inverters maximum output power depends on two factors; one is the max current rating of transformer’s primary winding and other factor is the current rating of driver transistors.

Transformer: Use a 12v-0-12v, 10A step-down transformer in reverse. That’s mean secondary winding (12v-0-12v) will be the primary and primary winding (220VAC side) will be the secondary (output). So that it will worked like a step-up transformer. You can also use a 5A transformer instead of 10A, if you couldn’t have 10A.  But the output power will decrease to 60 Watt.

+12VDC: A good quality 12V car battery could be used for DC 12V.

Parts list of 100watt inverter:

VR1 = 250K (Variable resistor/POT)
R1, R2 = 4.7K-1/4W Resistor
R3, R4, R5, R6 = 0.1R-5W
C1 = 0.022uF
C2 = 220uF-25V
D1 = BY127 Diode
D2 = 9.1V Zener Diode
Q1, Q4 = TIP122 Transistor
Q2, Q3, Q5, Q6 = 2N3055 Transistor
F1 = 10A Fuse
IC1 = CD4047
TX = 12-0-12V, 10A Step-down Transformer
Continue reading[...]

Schematic diagram for the One Transistor FM Radio with Improved Audio Gain

0 comments
Schematic diagram for the One Transistor FM Radio with Improved Audio Gain
One Transistor FM Radio with improved audio gain.
Some wiring notes:
Unless you have experience with super-regenerative radios, I highly recommend using the FAR Circuits printed circuit board.

Connect the two sections of the variable capacitor (C3) in series to linearize the tuning somewhat. That is, use the connections on either end of C3 and dont use the middle lead.
L2, the RF choke should not be near a ground. The same is true for L1. Capacitance to ground will disturb the feedback.

The gain is just enough to drive an earphone. If you live too far away from radio stations, you might have trouble hearing one. There is no option here for an external antenna (that would require and extra transistor).

You can drive a speaker if you add an external audio amplifier.
If you want a little more audio gain, or you cannot locate a TL431CLP chip, you can use some other audio amplifier in the circuit where pins 1 and 2 of D1 normally connect. You can use an LM386 or a TDA7052 audio amplifier. Quasar DIY project kit #3027 is a complete TDA7052 audio amplifier kit and it works fine in this application. 
Continue reading[...]
Blog host by Blogger.com & | Supported by you